| Blogs | Forums | Photo Album |
volume  
I`m a guitarist thinking of building my own volume and expression pedals (two seperate). Any one have any ideas on how to get started? The biggste problem seem to be, after doing a litlle research, ...
I have a Fender Strat, and I heard that to get a better output, you could re-wire it so your volume knob isn't in the way. I don't usually use my volume knob, unless I just want to put my g...
Tone cap mod for volume knob on guitar:
What is this exactly and where can I get it online?
Is it easy to install? just capacitor? Any diagrams anywhere that show the specs and/or installati...
What is a good volume pedal? I have been thinking about getting one.
Sometimes it would be nice to have the flexibility of turning down/up while maintaining the same plucking intensity.
My leccy guitar has a problem
When I turn the volume on one of the pickups up to top it cuts out or crackles until I fiddle with the knob
I remeber hearing solutions to this without rewiring, is...
Hi, all, I have an old Ernie Ball volume pedal that has a 100k linear taper pot.
I am trying to replace that with a higher value (250k) pot, and I'm wondering what taper I should use for a s...
I want to replace a noisy volume pot on a recent Mexican Fender Precision bass.
Original value: 250 KOhm.
A: Do I need linear or log taper? - or something else?
B: Will there be any benefit in ...
Hi
My strat is making noise when the volume pot is in the middle range. so anthing around 5 is really bad, up till two and from 8 its ok.
anyone know what causes this and how it can be fixed?
than...
...e cai i buy the kevlar tension wire (..the one wich make the potentiometer turn around..) that is in the Volume Pedals by Ernie Ball? thanks......
I am having volume issues with my new OCD v4 pedal. It doesn't seem to have the same punch as the rest of my pedals. any Idea why?
Hi
I have problem neighbors who I risk annoying if I play with my amp on louder than 5 I was wondering if playing quietly would all the time would damage my amp?
...s in any combination. Ideally this would be a circuit that would:
a) replace the three existing pots (volume, tone, tone) with an independent volume control for each pickup, b) do away with the to...
i use my EQ at the end, after i set the EQ volume up 1/4 pass the middle mark, I turn the volume down on my guitar half way, then adjust the amp volume right were I want it. This way I boost the vol...
The little knob is the volume control when you're in the active pickup. The larger knob below it is the blend knob. If I rotate the bottom know counter clockwise, I get no sound either, but thats...
I've used a Fender Deluxe 22 watts with no master volume for some 20 years and often told I'm too loud? How can this be? Volume is set at 2 1/2. These days, amps are mic'd into PA syste...
Huh. Well mine certainly plays loud and clean, but if I set the volume at 10 and otherwise turn up with the master volume, the sound does break up. In a pleasing way I mean. I understood that was a...
I would like to add a little custom wiring to my bass, that would allow me to replace one of my volume pots with a push/pull type pot, that I could use as a series parallel switch, a la the Fender S-1...
I'm curious about the Marhsall DSL2000.
It's small, does it work out ok for low volume practice in an apartment if you turn down the master volume?
I've been considering the VOX V...
...orks far better. Put the noisy little bastards in the loop, such as the CS, the SD and the PS.
- Put the volume pedal at front to enable volume swells with delay trails.
- Put time-based fx at the e...
...y of cleaning it except by moving it up/down quickly a couple of times and it goes away. Lower down the volume when doing this as the crackling can be loud.
Very bad hum is normally some groundin...
...tt and Jim, I'd add one thing about setting up your pickups. Start by getting them even in terms of volume.
I start with the bridge pickup. I set it for height first, trying to get the best ...
...ows.
from the earth terminal on the jack, run a wire to the ground which is normally on the top of the Volume pot. Then from the positive (Or live) side of the jack run a wire to the Middle termina...
depends on the amp volume before you add the tube screamer. I use a Marshall
Bluesbreaker combo, and if i have the amp up on around 5 or higher then add a little bit of the overdrive on the tube scre...
...e an electrical problem. I've had it for less than two weeks and all of a sudden unless both pickup volume dials are at max, there's a loud hum. Same deal when either of the two is turned ...
The Content on this site is provided for general information purposes only. It can not and should not be a substitute for face-to-face professional advice. By entering this site you declare you read and agreed to its Terms, Rules & Privacy.
Copyright © 2006 - 2009 Axe Central |
Sponsored LinksLatest Posts
|
more posts...