My Profile

Keep Up to Date:
Blog RSS
Blog
Forum RSS
Forum

volume

...ups in any combination. Ideally this would be a circuit that would: a) replace the three existing pots (volume, tone, tone) with an independent volume control for each pickup, b) do away with the to...
Tone cap mod for volume knob on guitar: What is this exactly and where can I get it online? Is it easy to install? just capacitor? Any diagrams anywhere that show the specs and/or installation
I`m a guitarist thinking of building my own volume and expression pedals (two seperate). Any one have any ideas on how to get started? The biggste problem seem to be, after doing a litlle research,
...a time) are all Boss. Chorus CH-1 Flanger BF-3 Digital Delay DD-6 Metal Zone - MT-2 TU-2 Tuner Ernie Ball Volume Pedal Which effects should I run through the FX loop, and which should I run direct to...
...parties with no additional PA and has been loud and clear. Has one overdrive footswitch with independent volume and gain controls that get even louder. It's in perfect working condition except for o...
...p for the individual coils of each humbucker. Finally, since the circuit really wouldn't support multiple volume and tone controls, I figured I'd fill in the remaining two holes (where the original to...
I would like to add a little custom wiring to my bass, that would allow me to replace one of my volume pots with a push/pull type pot, that I could use as a series parallel switch, a la the Fender S-1
...ou use to drive the guitar speaker, and the guitar speaker. This can be used to incrementally reduce the volume late at night (alas, reducing the amount of highly desirable, even though subtle, speak...
Hi, all, I have an old Ernie Ball volume pedal that has a 100k linear taper pot. I am trying to replace that with a higher value (250k) pot, and I'm wondering what taper I should use for a smoothe
I have a Fender Strat, and I heard that to get a better output, you could re-wire it so your volume knob isn't in the way. I don't usually use my volume knob, unless I just want to put my guitar down
I've got an early 70's silverface quad reverb. With the main volume on 6: The normal channel is completely clean up to pre-amp 10. But the vibrato channel starts distorting ( in an ugly manner ) on pr
...o a cab simulator I hear the same thing). Is this simply a quality of tube amps? Does it have to do with volume? I am dying here. And if I back off on the gain it sounds even worse. Can some of you p...
... (Demeter Tremulator), even with the mods and shipping costs. All mods I've come across deal mainly with volume loss of a stock TR-2. Analog Man offers a $45 mod (http://www.analogman.com/boss.htm#tr...
...I gigged with it last night and it sounded great. No longer directional. I think I may have lost a little volume but not much. The biggest changes in sound were that it cut the mids considerably. But ...
...2) 7. Boss Noise Suppressor (NS-2) 8. Boss Super Overdrive (SD-1) 9. Morley Bad Horsie Wah 10. Ernie Ball Volume Pedal I do it this way: [Morley Wah]--[TU-2]--[CS-3]--[CH-1]--[DD-5]--[PS-5]--[SD-1]-...
...t have an electrical problem. I've had it for less than two weeks and all of a sudden unless both pickup volume dials are at max, there's a loud hum. Same deal when either of the two is turned down ...
...kmaster is a 3 channel preamp Clean, Crunch and Ultra It has four 12ax7 tubes I lost the majority of the volume on the Ultra channel, the tone appears to be there but volume is very low compared to o...
...the neck position different from a J pickup? For reference, I play a Jazz Bass with both pickups at full volume. Every now and then I favor the bridge....
...t.guitar.effects dated 3/7 re. the Electro-Harmonix Deluxe Memory Man reissue mentioned a drop in signal volume when the effect is engaged. To date I have only observed this problem in units equi...
What is a good volume pedal? I have been thinking about getting one. Sometimes it would be nice to have the flexibility of turning down/up while maintaining the same plucking intensity.
...ike an almost phasor type effect sound to it and it was feeding back like mad. Even feeding back when the volume was off on my guitar. I tried the same with the Distortion channel, which definitely sh...
...d placed it at about 1/3 between edge of one speaker and middle of speaker. Preamp Section full, Master volume at bedroom level so that the amp only starts to say hello to you ;-) Results can be h...
I want to replace a noisy volume pot on a recent Mexican Fender Precision bass. Original value: 250 KOhm. A: Do I need linear or log taper? - or something else? B: Will there be any benefit in repla
My leccy guitar has a problem When I turn the volume on one of the pickups up to top it cuts out or crackles until I fiddle with the knob I remeber hearing solutions to this without rewiring, is it
...ne. That problem solved, my dear wife started complaining about how loud it was sounding - a look at the volume setting - it was on 3 - damn this thing's louder through the 4x12 at the same settings ...
...mber and any other information like wattage, to be accurate. Test - turn up the reverb top high with the volume at normal level and reverb switch on.. Pound the top of the amp with your fist. Do you ...
...antalum cap in parallel to see what happened. This *really* opened the tone up, and increased punch and volume considerably, but the tantalum was noisy as hell! I replaced both with a .015 OD, and ...
...nt to be able to use them "on the fly" without have to dance around on 11 different pedals. I want preset volume levels. And I want a wide array of interesting effects to give flavor and color to the ...
...ys find myself needing it on the bridge PU instead. As i'm installing some new pups (which come with new volume and tone pots so i'll be switching them out anyway) i decided to take this chance to do...
...rets. Some have jumbo frets some don't. Decide which you like best.. Once you have it plugged in turn the volume up to max and talk in to the pickup. If you hear your voice coming from the amp the pic...
Hey ppl, i'm thinkin about gettin a slave amp to amp up my volume on stage, at the mo i'm using a marshall B65. i'm on abit of a budget thats why i'm not gonna get a more powerful amp. thinking about
... I recently had these Aero pickups installed. They have a great sound, but are noisy when either pickup volume is turned down at all, so I have to play wide open all the time. This noise is really ...
...a huge part) sound coming into the mic. 2) Changing the amount of dynamic compression that the actual volume of the speaker is causing in the mic's diaphragm, ribbon or voice coil. You are changin...
...rth because of the *significant* signal increase when switching to the humbucker. But backing off on the volume knob of the guitar for me a) it's not accurate (I never put it to the same volume leve...
... Valvestate VS100R (with FX loop). Can anybody advise the best method for setting up the amp i.e. a/ VOLUME KNOB (clean) b/ FX MIX KNOB c/ FX LOOP LEVEL (10dB) PUSH-SWITCH ~ seems be best `out...
Page: 12

Copyright © 2006 - Jan 2009 Axe Central