I've got a problem with my 65' Deluxe Reverb reissue!!
The vibrato channel has begun to sound very strange when I'm using it with distortion/overdrive - the sound gets extremely weir...
I have a new Mexican Jazz Bass that I think might have an electrical problem. I've had it for less than two weeks and all of a sudden unless both pickup volume dials are at max, there's a l...
Had a similar problem with a Boogie Rectoverb, changed the tubes and problem resolved. Mine was a few years old and had original tubes so I replaced them all and didn't take time to isolate the ...
...e others. If one is you need a fret job on your guitar any any good luthier should be able to correct the problem.... Last problem could be that the guitar was not properly set up - have it checked ...
I have a 1996 Les Paul Classic Plus,and the original adjustable bridge is a problem...Now, for a guitar this nice and kinda expensive the adjustable saddle bridge is really junky!
It has alot of f...
Hi Guest. I personally would steer away from WD-40 for your problem as it could create many more if it gets into the wrong places.
If I understand you correctly its the case that sqeaks.? If tha...
Hi All:
Got a problem.... I'm on the road working so I can't carry a 10 watt practice amp with me - but do carry my MIM Stratocaster. I have this little "amp plug n play" which ...
It's the pocket sized one, not the rack mountable dtR-2.
I've had this tuner for 10 years, and now, when I turn it on, all it does is cycle through the LEDs repeatedly. The battery measure...
...ple of ways however, it depends on the size of the room that you are going to soundproof...I overcame this problem very cheaply, I had a headphone socket in the amp which of course cuts out any exteri...
I would go to Korg web-site and contact Technical Support and present the problem to them for their disposition and/or recommendations to correct the noise problem.
Regards,
kcbuck
Jake:
I do not understand what the problem is or what equipment you are talking about other than it's a resistence problem of some sort. Please clarify....
Regards,
kcbuck
Perhaps it is not very common but I most certainly have heard about this problem before. Usually sanding and treating it with specialized spray helped. If you need more info I will look it up for you ...
.... If this is the case, I would let a professional do a fret job on your Telecaster and correct the height problem.
QUESTIONS:
1. Have you done anything to the guitar lately that may have caused t...
...ay, many of the user reviews I've been reading for the lower cost basses mention fret buzz as being a problem. At first I just figured these were inexperienced players who didn't know anythi...
...n volume and expression pedals (two seperate). Any one have any ideas on how to get started? The biggste problem seem to be, after doing a litlle research, to find a propper housing. The pots, jack...
Hello Adam, welcome to the forum
I heard about this problem before but no-one found out what's the problem causing it though. I heard of many returning the product to their guitar center (or...
...ey securely treaded into the each post? If not, screw them in and make them secure.
If that is not the problem the guitar may need to be checked out by a luthier to identify the problem and get it...
...d (tuning peg) is a simple fix.... You may want to try and fix it or replace it, thats your call. 3 basic problems can cause freeze up..1) The shaft that the string is attached to is frozen in the bu...
...this proble before and refer to it as a "Twangy G String" no pun intended. What was creating my problem was when I changed the strings out prior to this the G String was not properly (fully...
Hi Guest:
I have had this same problem. The cause is that the string is not in the nut properly. Try loosening the High e string, take it out of the nut, and retighten the string ensuring that it i...
...though you widened the slots. If the wound strings "ping" when you tune them that could be your problem.
If everything is stock you might want to give PRS a call. They are a good compa...
...laced the stock neck on a Standard strat with a new one bought from AZGuitarParts. When installed the main problem at first was the allignment angle of the neck which when corrected with a bit of sand...
...e string and batch details to Fender and as in your case they sent a nice letter saying they had a machine problem with the D in that batch and that my comment that it would never tune until hell free...
Hi Boilerman:
Sounds like a dust problem to me. For starter is it a tube amp or all electronic?
1. Electronic; I would get a few cans of contact cleaner and clean all the printed circuit boards, ...
Hi Guest, welcome to our forum. There are a few things to check out ref your volume problem...You have done one of the things by trying a different guitar, you have now illiminated it being an amp pr...
... string height is increasing over time.
I wonder if adding a shim at the neck/body joint could fix this problem. Where do I place it? At the bridge side of the body pocket or the nut side? Any go...
...stor to use. Look at questions 23 and 24 for more details.
I also read about other solutions to the problem of losing highs when turning down the volume. I think one was to use some kind of pr...
The Content on this site is provided for general information purposes only. Your use of the Content, or any part thereof, is made solely at Your own risk and responsibility. By entering this site you declare you read and agreed to its
Terms, Rules & Privacy.
Copyright © 2006 - 2010 Axe Central